Meguiar's M105
Ultra Cut Compound
32 oz.
  Meguiars M105 Ultra Cut
Compound
Meguiars M105 Ultra Cut Compound,
revised formula,
utilizes new, abrasive technology to quickly remove damage and defects from the
paint’s surface without scouring the finish. The revolutionary abrasives in
Meguiars M105 Ultra cut Compound are so advanced and milled so perfectly that
the polish produces flawless results regardless of how it is applied. Ultra Cut
Compound will produce professional-looking results when applied by hand, random
orbital, dual-action or rotary machine polisher. The ultra fine, ultra hard
abrasives used in Ultra Cut Compound do not degrade in quality or cut during
application. This polish can remove up to 1200 grit scratches, sanding marks,
pig tails, acid rain damage, scuffing, and bird bomb etching effortlessly while
finishing to a very low swirl, high gloss. The “non-diminishing abrasives”, used
in M105 Ultra Cut Compound are fine tuned to remove microscopic amounts of paint
quickly yet still leave the paint glossy, shiny, and haze-free. The revised
formula of M105 Ultra Cut
Compound can remove paint defects by hand or with a random orbital or
dual-action machine that previously required a high-speed, rotary polisher. (The
older formula of M105 was not recommended for random orbital or dual-action
machines.)
When working with Ultra Cut Compound,
you should polish until the paint defects are removed and then stop. Because the
abrasives do not break down, the polish does not need to be overworked to
achieve results. The nature of Meguiars M105 Ultra Cut Compound requires
that pads be cleaned often. Spent paint, the paint removed during
polishing, can build-up in the pad and cause haze and swirls.
Net weight 32 fl. oz.
Directions:
For use by hand - Apply a small amount of polish to a White, Foam
Polishing Applicator and work in even, back and forth, motions until the
damage is removed. Buff off residues with a clean Microfiber cloth. Meguiars
M105 Ultra Cut Compound is perfect for hard-to-reach areas. It is the ideal
polish for removing water spotting and finger nail scratches under door handles.
Defect removal using a
random orbital or dual-action machine - Prime the pad with an ample amount
of M105. Rub it in aggressively (by hand) to ensure complete pad coverage (pad
feels moist to the touch).
For most polishing and compounding tasks a slower speed
setting is desirable as it helps to minimize fast evaporation of M105’s
lubrication. M105 will effectively cut defects at a very low speed setting. It
typically yields great results on a speed setting of 3-1/2 to 4 for the Porter
Cable 7424. For HEAVY defect removal, you may have to use the maximum speed
setting. Maximum speed really shortens the working-cycle of the polish, and
definitely abuses the polishing pads. If you must use high speed, swap pads
often during your polishing session.
It is not necessary nor is it desirable to create an excess buildup of M105 on
the pad. Too much buildup above the surface of the pad can decrease overall
performance. AVOID priming the pad with a fine mist of water, Final Inspection,
Last Touch, (or any other similar product). Why? While wetting the pad or
surface increases wetness, it does not necessarily add lubricity. In fact, if
too much wetting agent is added, it can help to wash away (or displace) the
buffing liquid’s built-in lubricating ingredients.
Use normal to heavy CONSISTENT downward pressure, combined with very slow
movement of the machine (as slow as one inch per second). Four to six slow
passes should do the trick. Once the product has run its working cycle, wipe the
surface clean. If the wipe off is difficult, mist the paint with water or a
wipe-off spray, wait a few
seconds, then wipe. If some residue remains, apply a bit of M105 to a dampened
microfiber cloth then buff the surface. AVOID using any other cleaners,
polishes, or waxes to remove residue! Many products contain oils, solvents,
etc., that may temporarily alter the surface hardness, slipperiness, etc., of
the paint. Inspect, and if needed, reapply M105 and repeat the defect removal
step. Wipe surface completely clean when all defects are removed. Reapply as
needed to completely remove remaining surface defects.
Final polishing using a random orbital or dual-action machine - Once
you’ve satisfactorily removed surface defects, prepare for final polishing using
a Lake Country, CCS, white polishing pad. Prime the pad (as previously
recommended). DO NOT USE AN ABUNDANCE OF PRODUCT. For polishing, a primed pad is
essential to satisfactory results. LESS working liquid (rather than MORE)
delivers the best finish. Use a slow to medium speed setting of 1-1/2 to 3-1/2
on the Porter Cable 7424. You cannot overuse M105, as long as the pad stays
moist (and it shouldn’t scour).
Once your working cycle is done, evaluate the surface. If you feel the need to
repeat the polishing process, use the following method (random-orbital ONLY):
Set the pad onto a microfiber cloth and turn the machine on. The microfiber will
remove a majority of the residue, oils, and paint from the pad. USE CAUTION-
Make sure the towel does not get caught in the drive mechanism!
Repeat the same process at least once more, but use a bit MORE pressure and even
LESS product during your second application. Some paints yield even better
results when the pad is simply cleaned, and NO ADDITIONAL PRODUCT is applied.
There is a learning curve involved when attempting to final polish paint with
this method. Take the time to give this step a chance. When done correctly, the
final finish should be stunning. |